Note: You need to purchase LightBurn before using it.įor details about how to use XCS to operate xTool D1 Pro, see " Use xTool Creative Space (XCS) to Operate xTool D1 Pro."įor details about how to use LightBurn to operate xTool D1 Pro, see " Use LightBurn to Operate xTool D1 Pro."įor details about how to create with example projects, see " xTool D1 Pro Example Project Files and Tutorials."īefore creating your works, you can place the aluminum sheet in the working area of xTool D1 Pro to protect your desk or floor from being smoked or burned.
#TIGHTEN PRO SOFTWARE#
You can operate xTool D1 Pro by using our official software xTool Creative Space (XCS) or the third-party software LightBurn. It's recommended that you adjust the position of the rear plate according to the thickness of the material to be processed.Īfter adjusting the position of the rear plate, you can still use the focal length setting bar to set the position of the laser module. To cut thicker materials, you can adjust the position of the rear plate on the laser module, based on the scale with which the focal length setting bar is aligned, to ensure better cutting performance. (Applicable only to the laser module of 20W) Set the position of the rear plate on the laser module Loosen the thumb screw on the other side and slide the laser module upward or downwardĪfter determining the position, tighten the thumb screw and put the focal length setting bar back Try to set the timing belts on the right and left plates to the same tension, so that xTool D1 Pro can cut and engrave materials properly. Otherwise, the limit pieces may be damaged. Prevent the middle plate and laser module from falling down themselves. Rotate the handle to tighten or loosen the screw The handle goes back to the default position. Hold the handle to draw it away from the threaded part. If the handle is blocked, you can tighten or loosen the screw as follows. You may need to repeat this process multiple times to tighten the thumb screw. Rotate the handle to stop it from being blocked Hold the handle to draw it away from the thread part (4) Use the thumb screw to fit the laser module. (3) Fit the laser module on the middle plate. (2) Connect the main control board and laser module.
#TIGHTEN PRO INSTALL#
(1) install the nozzle connector and insert the plug. (3) Use cable ties to fix the connection cables on the right plate. (2) Insert the connectors of the laser module, motor, and limit switch connection cables into the ports on the main control board, respectively. (1) Connect the limit switch component on the middle plate to the one on the slider of the left plate. Otherwise, the timing belt may be damaged. The screw is used to set the tension of the timing belt. (4) Use the screw to fit the timing pulley. (3) Align the middle plate with the screw holes on the sliders, and use screws to hold the middle plate and sliders together. (2) Insert the connector of the motor cable into the port on the motor. (1) Cut off the white cable ties on the middle plate and reserve the black ones. (2) Use cable ties to fix the motor cable on the front plate. Pay attention to the front and back sides of the connector. (1) Insert the connectors into the port on the main control board and the one on the motor, respectively. (4) Fully tighten the two screws on the coupling. (3) Slide the two sliders down against the front plate. Note: Keep a small distance between the coupling and motor, or the coupling can't rotate properly. (2) Slide the coupling to the joint of the shaft and motor shaft. You can adjust its tension by turning the screw. If you can't put the shaft through the timing belt, the possible cause is that the timing belt is set too tight. (1) Put the shaft through the coupling, and then put it through the timing belt and insert it into the idler pulley. Otherwise, the timing belts may be damaged. The screws are used to set the tension of the timing belts. (4) Use screws to fit the timing pulleys. (3) Use screws to hold the side plates together.
Align the power switch, power port, and USB port with the openings on the right plate. Note that no scissors are included in the pack. (1) Cut off the cable tie on the right plate. XTool D1 Pro Golden Red_Instructions_02.pdf Unbox and checkĪssemble xTool D1 Pro 1. XTool D1 Pro Golden Red_Instructions_01.pdf
#TIGHTEN PRO PDF#
Connect the motor on the left plate to the main control boardĬlean the laser module PDF files downloadĭ1 Pro Golden Red with RA2_Quick Start Guide.pdf
0 kommentar(er)
